Adding Hosts/PCs to GNS3 - VPCS Configuration Guide
Tuesday, 3 June 2008
For some time now I have been asked how I simulate hosts in GNS3 and my stock answer was to configure a router as a host by issuing the "no ip routing" command and setting a default gateway with the "ip default-gateway" command. You would also need to assign an IP address to the interface connected to the router performing routing, or a switch which in turn is connected to a router doing the routing. It worked a treat but had one major flaw, namely, CPU overhead.
I know that a lot of people tried putting loopback adapters at either end of a topology but when pinging between multiple loopback adapters the traffic stayed on the PC and would not pass through the routers configured in GNS3.
By jove though, a clever man, mirnshi I believe his name is, has devised a great little program that can simluate up to 9 hosts within GNS3. It is called VPCS and can be downloaded from here.
In my traditional style I shall run you through a step-by-step guide of configuring VPCS and show you an example of how I set up a basic topology to test the functionality.
1. Download the zip file from here and extract it to wherever desired.
2. Go to the GNS3/Dynamips directory and rename the cygwin1.dll file to cygwin1.dll.old and copy the cygwin1.dll file in the VPCS directory to this directory.
3. Open up a command prompt and change the directory to where you have the VPCS folder. If you are unsure of how to do this, go to Start-->Run and type in "cmd" (without the quotes) and hit Enter. Now using Windows Explorer go to the folder where VPCS is located and copy the location from the address bar. If you cannot see the address bar go to View-->Toolbars and click Address Bar. Now go back to the command prompt you opened and type "cd" (again, without the quotes) followed by the path to your VPCS folder. For example, I may have cd C:\Program Files\GNS3\vpcs-0.14g
An even easier way to do this in Windows XP is to download the "Open Command Prompt Here" Power Toy from here.
Once installed right-click the VPCS folder and select Open Command Prompt Here and a command prompt window will open in that directory. Windows Vista includes this ability right out of the box, it's just not immediately obvious, because it's hidden behind a shortcut key. To activate this, just hold down the Shift key when you right-click on a folder, and you should see the Open Command Window Here menu item.
4. To run VPCS type vpcs.exe from the command line and you ought to see a screenshot similar to below:
5. Type in the show command to view a printout of your virtual PCs.
6. To view the help type ?
I don't know who Mike Muuss is by the way, lol.
7. To change the IP address and default gateway to better suit your needs the following syntax prevails:
ip [ip address of PC] [ip address of default gateway] [mask in number of bits]
For example:
8. To change the virtual PC you are configuring simply enter the number of the virtual PC you wish to configure.
9. Keep adding as many PCs as you need and configure the IP addresses as desired (limited to 9).
10. Make a note of the LPORT and RPORT settings (from the show command) for each PC you have configured as you will need them for later.
Now the proof of the pudding is in the eating so what I'm going to do is connect a very simple network in GNS3 (I know this seems obvious but KEEP VPCS RUNNING):
NOTE: Each PC is a separate cloud.
11. Right-click on each cloud, choose Configure and then select the NIO UDP tab. You should now see a screen similar to the following:
12. Referring to step 10 where you noted the LPORT and RPORT values for each PC you need to add the RPORT value to the Local Port field in GNS3, the IP address 127.0.0.1 in the Remote Host field in GNS3, and finally the LPORT value in the Remote Port field in GNS3. Once you have finished this ensure that you click on the Add button and select Apply, then OK. For example if my LPORT value was 20000 and my RPORT value 30000 then I would fill it out thus:
13. Now connect your network in GNS3 end-to-end and assign IP addresses as apt to the routers. Remember to either run a routing protcol between the two routers or use static or default routes. For my purpose I used default routes on each router pointing to the other router.
For example in my IP addressing scheme I have:
PC1 to R1 Fa0/0 = 192.168.1.1/24 and 192.168.1.254/24 respectively
R1 Fa0/1 to R2 Fa0/1 = 192.168.0.1/24 and 192.168.0.2/24 respectively
R2 Fa0/0 to PC2 = 192.168.2.254/24 and 192.168.2.1/24 respectively
My default routes are:
R1: ip route 0.0.0.0 0.0.0.0 192.168.0.2
R2: ip route 0.0.0.0 0.0.0.0 192.168.0.1
My network looks like this now:
14. Go back to VPCS. Here I have tested for end-to-end connectivity by pinging from PC1 to PC2:
"So what?" I hear you cry. I know this doesn't prove whether the traffic passes over the GNS3 routers. That is where we use the tracert command in VPCS. Check it out:
Would you look at that! Hop 2 is the Fa0/1 interface of R2. Proof that the packets traverse the routers.
I must say that this is a major breakthrough for me and hopefully for others and will save a lot of time and CPU resources.
Enjoy!
Chris
Posted byChris Bloomfield at 11:09 34 comments
Labels: cygwin, gns3 dynamips, host, loopback, mirnshi, pc, vpcs
GNS3 Configuration Guide
Tuesday, 18 December 2007
What is GNS3 I hear you cry? Well, imho, it is the best tool on the market to practice router configuration without having an actual router in front of you. What sets it apart is that it is a Cisco IOS emulator, not one of those nasty simulators that constrain the commands that can be used. The caveat is that you will need a Cisco IOS, for example I use the 3660 Crypto IOS. I have a support contract with Cisco so I can access an IOS however if you look around enough you will be able to find a Cisco IOS for yourself.
GNS3 is actually the graphical front-end of Dynamips/Dynagen and allows you to drag-and-drop routers onto a stage, connect them up, run IOS on them, and save their configs, just as if you had your own network. It can be a little confusing to set up first of all so I will present a step-by-step guide below of how to install and configure GNS3 including a couple of advanced options which will allow you to run Cisco Security Device Manager (SDM) on your PC.
Installation and Configuration
This process needs to be done only the once.
1. Download GNS3 from here and choose the installer which includes Dynamips, WinPCap and the binary version of GNS3 and install, accepting the various licence agreements etc.
2. You now need a Cisco IOS. Get one from Cisco if you have a CCO account with Support or find an IOS on Google.
3. Now open up GNS3.
Users of GNS3 version 0.5 will see the following: 
4. Now click on Step 1.
You will see something similar to the following: 
5. The executable path should point to the dynamips-wxp.exe in the Program Files directory. Change the Working Directory to a desired folder then click on the Test button. You should see that Dynamips has successfully started, if so click Apply then OK. If not you should double-check the Executable Path and the Working Directory:
6. Go back to the Setup Wizard and choose Step 2 and you should get a screen similar to below:
7. In the Settings section you need to point to the IOS image you copied in Step 2 and select the platform and model, then click on Save. The value of the IDLE PC section will be blank and leave blank for now. Now click on Close. Click on OK to close the Setup Wizard.
8. On the main screen drag a router onto the main screen then right-click on it, select Start and wait for the IOS to start and then right-click and select Console. You should now get a DOS screen open up with a telnet session for the router. NOTE: The length of time you have to wait for this to start depends on the speed and memory of your PC. 
9. Say “No” to initial configuration dialog until you get to the Router> prompt. Now type enable to go into Enable mode.
10. Go back to the GNS3 session KEEPING THE CONSOLE SESSION OPEN.
11. Type idlepc get your-router-name for example idlepc get R0 and wait for some idlepc values to be displayed. Make a note of these values and click Cancel.
12. By default Dynamips will take up 100% of your CPU usage and you need to specify an idlepc value to get that changed. Close down the console session and open up Task Manager on your PC (usually CTRL-ALT-DELETE) then go to the Performance tab.
13. Go to Edit-->IOS Images and Hypervisors and select the IOS you identified in Step 4 then click on Edit. Enter the first idlepc value you wrote down from Step 12 then click on Save then Close.
14. Start the IOS again as you did in Step 8 then console to the router. View the CPU utilisation in Task Manager and see if it falls below 5%. If it stays at 100% then go back to step 14 and change the idlepc value to the next one in the list. Repeat this until you get an idlepc value that has the CPU utilisation at around 5% or less.
You have now successfully installed and configured GNS3.
Configuring a Serial Interface on a Router
By default the 3660 image that I use comes with 2 FastEthernet interfaces. In order to simulate WAN links you need to add serial interfaces to the router as outlined below.
1. Right-click on your router, choose Configure, then click on your router name.
2. Click on the slots tab and change slot 1 (or any other slot other than slot 0) to NM-4T. This will provide you with 4 serial interfaces. NOTE THAT THE SLOT NAME MAY BE DIFFERENT DEPENDING ON WHICH IOS YOU USE.
3. Click on Apply then OK.
Adding a switch module to your router
Follow the same steps as you did for configuring a serial interface but choose the NM-16ESW module from the drop-down list.
Connecting two or more routers
You will come to the point where configuring just one router is not sufficient such as when you want to run a routing protocol. The following guidelines show you how to connect routers together.
1. Drag two or more routers onto the stage and configure their slots if required. Display their hostnames by pressing the ABC button on the toolbar if they are not already displayed.
This is a personal preference and allows you to track which router is which.
2. Now click on the interface button on the toolbar and select Manual.
The interface button changes to a red cross.
Now left-click on a router and select an interface which you want a cable connected to. Now click the router to which you want to connect to and select the interface on that router for the other end of the link. You should now see the link has been drawn. Once you have finished configuring the interfaces click the interface button (red cross) to get out of interface configuration mode (the icon will revert to the telephone jack symbol). The picture below shows three routers with a FastEthernet connection and the other with a Serial link (zig-zag line).
3. Notice that each link has got a red dot on it. When you start the IOS each dot should turn to green which denotes that each router has successfully started the IOS.
Saving your configuration
After all your hard work on the command line you will probably want to save your configuration and reuse it on another day. Follow the steps below to save your work:
1. Go to File-->Save As and save your topology where you want as a .net file. When it comes to reusing this topology just double-click on the .net file to open it up in GNS3.
2. On each router save your config using copy run start
3. Back in GNS3 type save /all in the bottom half of the screen to save all of the configs into the .net file. If you want to save the config of only one router you can replace the keyword all with the name of the router you wish to save the config of. You can also extract the configs by clicking on the "Extract all start-up configs" button on the toolbar.
Configuring a host in the network (Advanced)
There may be an occasion when you want to connect a host in your topology such as running Cisco’s Security Device Manager (use of this may figure in future CCNA exams). To do this you must first configure a Loopback Adapter on your PC.
1. Go to Control Panel-->Add Hardware then click Next
2. Yes I have already connected the hardware
3. Scroll to the bottom and click on Add a new hardware device then Next
4. Install the hardware that I manually select from a list (Advanced)
5. Click on Network Adapters then Next
6. Select Microsoft as the Manufacturer then on Microsoft Loopback Adapter under Network Adapter then click Next then Next again.
7. Open up Control Panel-->Network Connections to see the adapter in place.
Now that you have created a loopback adapter you will want to connect it to a router. To do this, follow these steps:
1. In the GNS3 installation directory run the Network Device List.bat file which will give you the Ethernet address of your Loopback Adapter.
Notice the second adapter shown where description is MS Loopback Driver. I have renamed the adapter as Loopback Adapter for SDM. We are interested in the NIO_gen_eth string.
2. Go into GNS3 and drag a cloud onto the stage.
3. Right-click the cloud and select configure.
4. Choose your cloud from the list.
5. In the Generic Ethernet NIO section select your Loopback Adapter from the drop-down list (the one that matches what is shown in Step 1) and click on Add, Apply, the OK.
6. Now connect a FastEthernet port on your router to the cloud as you would connect two routers.
7. Configure an IP address and subnet mask on the router interface connected to the cloud and bring the interface up.
8. Go to Control Panel-->Network Connections and right-click your adapter. Choose Properties then Internet Protocol (TCP/IP) and give it an IP address in the same subnet as the router’s FastEthernet interface with the same subnet mask and with a default gateway matching the IP address of the router’s interface.
Example:
Router’s FastEthernet 0/0 interface connected to the cloud:
On the router I would have something like:
Router(config)#int fa0/0
Router(config-if)#ip address 192.168.1.1 255.255.255.0
Router(config-if)#no shut
On the PC I would have something like:
IP address = 192.168.1.2
Subnet Mask = 255.255.255.0
Default Gateway = 192.168.1.1
You should now be able to ping between your PC and the router
Running SDM (Advanced)
There may be a need to practice using the Cisco Security Device Manager (SDM) for your exam and the following steps show you how to configure it.
1. Download and install SDM from the www.cisco.com or from a share on the web.
2. Choose to only install SDM to your PC, NOT to the router.
3. Now configure your router with a hostname and a domain name in order for SSH to work:
Router#conf t
Router(config)#hostname SDMRouter
SDMRouter(config)#ip domain-name SDMDomain
4. Now configure your router with the following commands:
SDMRouter(config)#username your_username privilege 15 secret 5
SDMRouter(config)#ip http server
SDMRouter(config)#ip http secure-server
SDMRouter(config)#ip http authentication local
SDMRouter(config)#line vty 0 4
SDMRouter(config-line)#login local
SDMRouter(config-line)#transport input telnet ssh
SDMRouter(config-line)#privilege level 15
SDMRouter(config-line)#line cons 0
SDMRouter(config-line)#login local
SDMRouter(config-line)#transport input telnet ssh
SDMRouter(config-line)#privilege level 15
SDMRouter(config-line)#exit
SDMRouter(config)#crypto key generate rsa gen mod 1024
5. Now double-click the SDM icon and enter the IP address of the router and tick the box asking about HTTPS then click on Launch.
6. Ensure you allow popups on your browser.
7. Enter username and password as defined after step 3.
8. Say yes to allow SDM to install.
You should now have a screen similar to the one below although this may be because I used a username and password of “cisco” which are the default.
9. Select a new username and password for the router then click OK. You should see the screen below then click OK.
10. You should now be in SDM and able to configure the router.
Posted byChris Bloomfield at 09:11 67 comments
Labels: adapter, Cisco, configuration, dynagen, dynamips, emulator, gns3, guide, idlepc, ios, loopback, microsoft, NIO_gen_eth, router, sdm
